ObjectivesDeakin University's postgraduate Engineering program has been designed to strengthen, build on and extend students' understanding of engineering principles required for successful engineering careers in Australia and overseas. Students will gain technical skills, a positive approach to problem solving and the ability to work as a team to enable them to start work on complex projects immediately. Students can chose from six specialisms in Mechanical Engineering, Electronics Engineering or Civil Engineering. The six specialisms all provide students with expertise in areas of high demand for graduates. The program's focus on practical experience and a supervised research project or industry project provides students with advanced project management skills. This experience equips graduates with the ability to apply their skills and knowledge to practical, industrially focussed problems. The Master of Engineering can be undertaken as a stand-alone or exit qualification from the Master of Engineering (Professional) program.
Entry requirementsEntry to the Master of Engineering requires a four-year Bachelor of Engineering degree or equivalent.
Academic titleMaster of Engineering (International Students)
Course descriptionFees and charges
Fee paying place - International (IFP)
A Fee paying place is one for which the university does not receive any government funding. As such, students enrolled in these places are required to contribute the full cost of their course.
Fees for international students apply to persons living in Australia with Temporary Resident status, provided that there is no limitation on study and persons living abroad who are not Australian citizens and do not have Permanent Resident status in Australia.
Equivalent Full Time Student Load (EFTSL)
EFTSL is the standard annual full time load. Eight credit points is the standard full time load for one year of study.
* The 'indicative annual course fee' cited has been provided as a guide only. It has been calculated on the basis of a typical enrolment of a student undertaking the course in 2009, and reflects the cost involved in undertaking a full-time quota of units within the specified discipline.
The actual fees charged by Deakin University will depend upon the discipline from which each individual unit is chosen, and may vary from the indicative course fee cited, particularly if units are chosen from a number of disciplines. The cost of each unit offered in 2009 can be viewed at http://www.deakin.edu.au/current-students/handbooks2009/search.php.
Please note that the fees per unit/credit point may increase annually due to rises in the cost of course delivery and service.
Deakin assumes no responsibility for persons relying on 'indicative course fees' to calculate the total future cost of their course.
Course rules
To be awarded the degree of Master of Engineering, a student must successfully complete units with a total value of 12 credit points, including the following:
Two common core units from:
SEB711 Developing and Managing Innovation
SEN705 Engineering Professional Practice
SIT764 Project Management
and
A six credit point specialism in one of:
Mechanical Engineering (Product Design and Development)
Mechanical Engineering (Automotive Engineering)
Electronics Engineering (Automation and Control Systems)
Four elective units at level 7 (across the Faculty/University)
or
SEN701 Professional Practice 1
SEN702 Professional Practice 2
plus two approved elective units at level 7 (across the Faculty/University).
Equipment requirements
Students must have access to the Internet, a microcomputer, modem and printer to provide, via the telephone network, communication with Deakin University's on-campus computers. Prospective students may wish to contact the School of Engineering and Information Technology to obtain information about the hardware and software requirements, telephone 03 5227 2536.
Admission requirements - general
Deakin University offers admission to postgraduate courses through a number of Admission categories.
In all categories of admission, selection is based primarily on academic merit as indicated by an applicants previous academic record. The minimum requirements are successful completion of a three-year undergraduate degree, or equivalent, from an approved university or other educational institution or successful completion of other equivalent qualifications gained by examination, or approved professional or industrial experience. International students must also meet the English language requirements.
Admission requirements - specific
Entry to the Master of Engineering requires a four-year Bachelor of Engineering degree or equivalent.
Advanced standing - general
If you have completed previous studies which you believe may reduce the number of units you have to complete at Deakin, indicate in the appropriate section on your application that you wish to be considered for advanced standing. You will need to provide your previous course details so your credit can be determined. If you are eligible, your offer letter will then contain information about your advanced standing.
Your advanced standing is formally approved prior to your enrolment at Deakin during the Enrolment and Orientation Program. You must bring original documents relating to your previous study so that this approval can occur.
You can also refer to the Advanced Standing System which outlines the credit that may be granted towards a Deakin University degree.
How to apply
* Applicant Portal: Use our online application system to submit and track your application now.
* Apply through a Deakin International office: Fill out an application form and submit it to a Deakin International office.
* Apply through a Deakin representative: Take your application form to your preferred agent for assistance.
Tracking your application:
If you have already applied and wish to enquire about your application please refer to the relevant area through which you originally applied.
* If you applied online, log back into the Applicant Portal using your username and password.
* If you applied through a Deakin representative please contact your representative.
* If you applied through a Deakin International office please contact that office.
Exit points
Candidates may exit:
* with a Graduate Certificate of Engineering after completion of four level 7 credit points
* with a Graduate Diploma of Engineering after completion of 8 credit points, including two common core units and one specialism.